Skip to Content

Changes for page DIN-CENCN-2 Setup

Last modified by Alexander Mott on 2024/02/09 01:01
From version 17.1
edited by Alexander Mott
on 2023/12/12 00:01
Change comment: There is no comment for this version
To version 11.1
edited by Alexander Mott
on 2022/09/19 17:02
Change comment: Renamed back-links.

Summary

Details

Page properties
Content
... ... @@ -2,35 +2,29 @@
2 2  {{toc/}}
3 3  {{/box}}
4 4  
5 -DIN-CENCN-2s are Cresnet-to-Ethernet bridges which convert data over the Cresnet bus into high-speed Ethernet traffic. This helps avoid issues with bandwidth over the Cresnet bus for jobs which have a large number of Cresnet devices, as well as allowing for additional power supplies to provide power Cresnet devices. They are analogous to [[CEN-GWEXERs>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.CEN-GWEXER Setup.WebHome]] for Crestron wireless systems.
5 +(% class="row" %)
6 +(((
7 +DIN-CENCN-2s are Cresnet-to-Ethernet bridges which convert data over the Cresnet bus into high-speed Ethernet traffic. This helps avoid issues with bandwidth over the Cresnet bus for jobs which have a large number of Cresnet devices, as well as allowing for additional power supplies to provide power Cresnet devices.
6 6  
7 7  For SHOWRUNNER™ installations, the IP address of the DIN-CENCN-2 does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, DIN-CENCN-2s are identified to the processor via their IP-ID. Note that which Cresnet devices are landed at each Net of each DIN-CENCN-2 matters, and if devices are moved between Nets or between DIN-CENCN-2s then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the DIN-CENCN-2 IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. DIN-CENCN-2's will typically have IP-IDs in the "##Dx##" range.
8 8  
9 9  = IP Configuration =
10 10  
11 -Typically, each DIN-CENCN-2 will need to be initially configured via USB, unless their MAC addresses are already known and the lighting network has a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[ShowRunner™ DHCP Server>>doc:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.DHCP Server.WebHome]]).
13 +Typically, each DIN-CENCN-2 will need to be initially configured via USB, unless their MAC addresses are already known and the lighting network has a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[SHOWRUNNER™ DHCP Server>>doc:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Software and Programming.Troubleshooting.DHCP Server.WebHome]]).
12 12  
13 13  Whether connected to the DIN-CENCN-2 via USB or Ethernet, the process to configure the static IP addresses is the same:
14 14  
15 15  * Open Text Console in Toolbox and connect to the DIN-CENCN-2
16 16  * Run the following commands to configure the DIN-CENCN-2's IP settings (example is for a **10.0.0.0(% style="color:darkgoldenrod" %)/24(%%)** subnet, with a CENCN-2 IP address of (% style="color:blue" %)**10.0.0.12**(%%), a CENCN-2 IP-ID of (% style="color:olive" %)**D1**(%%), a processor IP address of (% style="color:orange" %)**10.0.0.10**(%%), and a hostname of (% style="color:purple" %)**CENCN-L1**(%%))
19 +** Disable DHCP: ##dhcp off##
17 17  ** Set IP address: ##ipa 0 (% style="color:blue" %)**10.0.0.12**(%%)##
18 18  ** Set IP subnet mask: ##ipm 0 (% style="color:darkgoldenrod" %)**255.255.255.0**(%%)##
19 19  ** Set default gateway: ##defr 0 **10.0.0.1**##
20 -** Disable DHCP: ##dhcp off##
21 21  ** Update IP table: ##addm (% style="color:olive" %)**D1**(%%) (% style="color:orange" %)**10.0.0.10**(%%)##
22 22  ** Set hostname: ##host (% style="color:purple" %)**CENCN-L1**(%%)##
23 23  ** Reboot the DIN-CENCN-2: ##reboot##
24 -* At this point, it is a good idea to [[update the device firmware>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.Updating Firmware.WebHome]]
25 25  * Repeat for all DIN-CENCN-2s on the job
26 26  
27 -= Useful Commands =
28 -
29 -Below is a list of useful commands that can be used with DIN-CENCN-2 to help with troubleshooting Cresnet issues.
30 -
31 -* ##ppndiscover## - this command scans each of the DIN-CENCN-2's Nets and prints out a list of connected Cresnet devices identified by their connection ID and their TSID
32 -* ##cnettest## - this command scans each Net and prints a summary of the number of devices on each net as well as any Cresnet issues found (e.g., "Y short to Z" or "Power Fault")
33 -
34 34  = Moving Cresnet Devices =
35 35  
36 36  In SHOWRUNNER™, which Net each Cresnet cable is landed on is important. Each DIN-CENCN-2 is firmware limited to a maximum of 25 Cresnet devices per Net, and which CENCN-2/Net each device is on is tracked in the configuration file. If devices are moved between DIN-CENCN-2s or moved between Nets on the same DIN-CENCN-2, then the configuration file must be updated. Every device in the configuration has a ##"DeviceHostId"## (the host DIN-CENCN-2's IP-ID) and a ##"DeviceHostBranch"## (the Net of the DIN-CENCN-2) associated with it.
... ... @@ -41,3 +41,4 @@
41 41  1. Cresnet IDs must be in the hexadecimal range 03 to 1B
42 42  1. Any children devices (such as NS occ sensors, photocells, GLPPA-KP keypads, etc.) must also be moved. If the parent Cresnet ID is changed then the children IDs must also be updated
43 43  1. If devices are moved from a DIN-CENCN-2 to be landed directly on a processor (or landed on a DIN-HUB on a processor), then the device host ID should be ##null## and the host branch should be ##0##
38 +)))