Skip to Content

Changes for page Zūm Discovery

Last modified by Austin Weygandt on 2025/05/02 20:21
From version 5.1
edited by Alexander Mott
on 2022/09/22 21:55
Change comment: There is no comment for this version
To version 7.1
edited by Alexander Mott
on 2022/09/22 23:59
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -Zūm Autodiscovery
1 +Zūm Discovery
Content
... ... @@ -1,6 +1,6 @@
1 1  (% class="box warningmessage" %)
2 2  (((
3 -This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Autodiscovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
3 +This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Discovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
4 4  For instructions on configuring Zūm Net devices using Crestron Toolbox, see [[this page>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.ZUMNET-JBOX Setup.WebHome]].
5 5  )))
6 6  
... ... @@ -10,28 +10,68 @@
10 10  
11 11  (% class="row" %)
12 12  (((
13 -If Zūm Net devices have been configured using Crestron's Zūm App
13 +If Zūm Wired or Wireless devices have been configured using Crestron's Zūm App, then it is possible to automatically build a SHOWRUNNER™ configuration file using the Zūm Discovery feature that is built into SHOWRUNNER™.
14 14  
15 -= Zūm Wired =
15 +There are certain pre-requisites and limitations when building a SHOWRUNNER™ configuration this way, and it may sometimes be necessary make some adjustments to the final configuration, such as changing keypad types and moving loads between areas.
16 16  
17 -Lorem
17 += Zūm Wired Discovery =
18 18  
19 -= Zūm Wireless =
19 +== Notes and Limitations ==
20 20  
21 -As of version 2.190 ShowRunner can discover RF Gateways and attached Zum NETBRIDGES. ShowRunner will find all devices, set them up, create areas and loads.
22 -*Disconnect from the gateway before discovery as they cannot support multiple connections*
23 -*Plug loads do not appear in the UI*
21 +* SHOWRUNNER™ version 3.014 or newer required
22 +* Zūm Wired firmware version 1.02.10 or greater required
23 +* Disconnect from any ZUMNET devices you may be connected to in Toolbox prior to running the discovery commands
24 +* Cresnet devices landed on Zūm Link will not be discovered (Crestron bug expected to be corrected in a future firmware release)
25 +* One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
24 24  
25 -== Pre-Requisites: ==
27 +== Steps ==
26 26  
27 -* Zum NETBRIDGES acquired to their respective gateway (CEN-GWEXER/ZUMNET-GATEWAY)
28 -* SHOWRUNNER™ installed and running on a 3-series processor on the same network as the gateway
29 -* NETBRIDGES do not need to have addresses assigned. SHOWRUNNER™ will automatically address them. If devices all already addressed then their addresses will be honored.
29 +1. [[Install SHOWRUNNER™>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.WebHome]] on the processor and configure the processor as necessary
30 +1*. Note that while Zūm Wired discovery will build a configuration, if a configuration file was provided then it should still be loaded as it may contain location data or non-Zūm devices.
31 +1. If the ZUMNET-JBOX firmware is too out-of-date to connect using the Crestron Zūm App, then there are some additional steps required: 
32 +1*. Connect to the first ZUMNET-JBOX in Toolbox
33 +1*. Configure a static IP address for the ZUMNET-JBOX if there is no DHCP server on the network 
34 +1**. Note: The SHOWRUNNER™ built-in DHCP server is not meant to be used in production
35 +1**. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
36 +1*. Set unique Connection IDs for each device hosted on the ZUMNET-JBOX so that their firmware can be updated
37 +1*. Load the Zūm Wired firmware to the ZUMNET-JBOX
38 +1*. Repeat the above steps for all ZUMNET-JBOXs
39 +1*. Once all the ZUMNET-JBOXs have pushed the new firmware to their hosted devices, proceed to the next step
40 +1. Connect to first ZUMNET-JBOX in the Crestron Zūm App
41 +1. Unique Connection IDs should be automatically assigned to any Zūm Link and Cresnet devices on the ZUMNET-JBOX
42 +1*. If firmware was out-of-date, then this step should have already been completed
43 +1*. If unique CIDs are not automatically assigned, connect to the JBOX in Toolbox and give the devices unique CIDs
44 +1. Configure a static IP address for the ZUMNET-JBOX if there is no DHCP server on the network 
45 +1*. If firmware was out-of-date, then this step should have already been completed
46 +1*. Note: The SHOWRUNNER™ built-in DHCP server is not meant to be used in production
47 +1*. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
48 +1. Optionally, manually configure the ZUMNET-JBOX IP table to point at the processor if you want to keep track of which ZUMNET-JBOX is at each IP-ID
49 +1*. If you do not manually configure the IP table, then SHOWRUNNER™ will automatically configure the IP-ID for each ZUMNET-JBOX during discovery
50 +1. Repeat from step 3 until all ZUMNET-JBOXs that are to be controlled by SHOWRUNNER™ have static IP addresses and unique CIDs for any hosted devices
51 +1. Connect to the processor in Toolbox and run the command: ##sr discover zumnet true false##
52 +1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding areas and loads to the configuration
53 +1*. One area will be created per ZUMNET-JBOX
54 +1. Run the command: ##sr discover zumnet true true##
55 +1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware on the previously discovered Zūm Net devices
56 +1*. This command **does not** bring in Cresnet devices: those must be added to the configuration manually until this issue is fixed in the Zūm Wired firmware
57 +1. Put all ZUMNET-JBOXs into CNET mode in order to allow full control from SHOWRUNNER™
58 +1*. Odd behavior may result from conflicts between SHOWRUNNER™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
59 +
60 += Zūm Wireless Discovery =
61 +
62 +== Notes and Limitations ==
63 +
64 +* Processor with SHOWRUNNER™ version 2.190 or newer must be running on the same network as the gateway(s) to be acquired
65 +** For SHOWRUNNER™ versions 3.014 and newer, replace ##sr discover zum## commands with ##sr discover zummesh##
66 +* ZUM-NETBRIDGES must already be acquired to their respective gateway
67 +* SHOWRUNNER™ will automatically address any ZUM-NETBRIDGES that do not need have addresses assigned, but will still honor any already addressed devices
68 +* Disconnect from any RF gateways you may be connected to in Toolbox prior to running the discovery command
69 +* Plug loads will not appear in the SHOWRUNNER™ UI
30 30  )))
31 31  
32 32  (% class="box warningmessage" id="HCaution:" %)
33 33  (((
34 -**Note:** SHOWRUNNER™ has two different approaches for Zūm Wireless Autodiscovery
74 +**Note:** SHOWRUNNER™ has two different approaches for Zūm Wireless Discovery
35 35  
36 36  1. **Manual RF Gateway Assignment** - SHOWRUNNER™ can be told which gateways it should scan. Use this approach if you have gateways that are used by multiple systems on the same local network.
37 37  1. **Claim All RF Gateways** - SHOWRUNNER™ will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own. **DO NOT** use this method if there are gateways used by different SHOWRUNNER™ or other Crestron systems on the same local network.
... ... @@ -39,7 +39,7 @@
39 39  
40 40  (% class="row" %)
41 41  (((
42 -== Manual RF Gateway Claiming ==
82 +== Manual RF Gateway Assignment Instructions ==
43 43  
44 44  Use this method if you have multiple SHOWRUNNER™ instances on the same network or have gateways used by other Crestron systems.
45 45  
... ... @@ -54,7 +54,7 @@
54 54  * Once SHOWRUNNER™ has finished restarting type "//sr discover zum false//" and press enter. SHOWRUNNER™ will be able to acquire the loads attached to the Zūm rooms at this point.
55 55  * Once completed SHOWRUNNER™ is now ready for full Zūm control
56 56  
57 -== Claim All RF Gateways ==
97 +== Claim All RF Gateways Instructions ==
58 58  
59 59  Use this method when you have a single SHOWRUNNER™ instance on a local network with all gateways being used for SHOWRUNNER™.
60 60  
... ... @@ -68,7 +68,7 @@
68 68  
69 69  == Examples ==
70 70  
71 -=== Claim Selectively (Manual) Example ===
111 +=== Manual Example ===
72 72  
73 73  {{{MC4>sr devmgr ethernet query
74 74  Ethrenet AutoDiscovery Result: AutoDiscoveryOperationSuccess