Skip to Content

Changes for page Zūm Discovery

Last modified by Craig Lewis on 2025/09/25 20:36
From version 40.1
edited by Alexander Mott
on 2025/04/03 17:35
Change comment: There is no comment for this version
To version 43.1
edited by Craig Lewis
on 2025/09/25 20:36
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.alexander\.mott@chiefintegrations\.com
1 +XWiki.craig\.lewis@chiefintegrations\.com
Content
... ... @@ -1,6 +1,6 @@
1 1  (% class="box errormessage" %)
2 2  (((
3 -ūūūūūū**IMPORTANT:** When using ShowRunnerCLC™ with a ZUM-HUB4, **do not** discover Zūm Rooms using the Crestron HUB4 Web UI. During discovery, the HUB4 will claim ZUMNET-JBOXs and prevent ShowRunnerCLC™ from auto-discovering or registering the Zūm hardware for itself.
3 +**IMPORTANT:** When using ShowRunnerCLC™ with a ZUM-HUB4, **do not** discover Zūm Rooms using the Crestron HUB4 Web UI. During discovery, the HUB4 will claim ZUMNET-JBOXs and prevent ShowRunnerCLC™ from auto-discovering or registering the Zūm hardware for itself.
4 4  
5 5  **WARNING:** Cresnet Discovery is non-functional for ZUMNET-JBOXs with certain versions of Crestron Device Database.
6 6  ShowRunnerCLC™ versions v3.019 through v3.041 must be either downgraded to v3.018 or upgraded to v3.042 or newer in order to perform auto-discover functions.
... ... @@ -85,6 +85,7 @@
85 85  * ZUMLINK-IOs will not be discovered (Expected to be discoverable in future ShowRunnerCLC™ release)
86 86  * ZUMLINK-KPs will not be discovered on older versions of ShowRunnerCLC™ (v3.058 or newer will discover keypads and set as remote type)
87 87  * One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
88 +* ZUMNET-JBOX-DALI will be created with only 1 broadcast load index 17. If ZUMNET is being setup as a LEGACY controller, the config will need to be updated to reflect the model as ZUMNET-JBOX-DALI-LEGACY.
88 88  )))
89 89  
90 90  == Steps ==
... ... @@ -140,6 +140,7 @@
140 140  
141 141  (% class="box warningmessage" %)
142 142  (((
144 +* **Newer GWEXER firmware enables SSL by default. Follow the instructions at [[SSL User Configuration>>doc:SHOWRUNNER™ User Guide & Wiki.SHOWRUNNER™ Appendix.SSL User Configuration.WebHome]] and manually add the IP Table entries on the GWEXER**
143 143  * Processor with ShowRunnerCLC™ version 2.190 or newer must be running on the same network as the gateway(s) to be acquired
144 144  ** For ShowRunnerCLC™ versions prior to 3.014 and newer, replace **##sr discover zummesh##** commands with **##sr discover zum##**
145 145  * ZUM-NETBRIDGES must already be acquired to their respective gateway
... ... @@ -146,7 +146,6 @@
146 146  * ShowRunnerCLC™ will automatically address any ZUM-NETBRIDGES that do not need have addresses assigned, but will still honor any already addressed devices
147 147  * Disconnect from any RF gateways you may be connected to in Toolbox prior to running the discovery command
148 148  * Plug loads will not appear in the ShowRunnerCLC™ UI
149 -* Newer GWEXER firmware enables SSL by default. Follow the instructions at [[SSL User Configuration>>doc:SHOWRUNNER™ User Guide & Wiki.SHOWRUNNER™ Appendix.SSL User Configuration.WebHome]] and manually add the IP Table entries on the GWEXER
150 150  )))
151 151  
152 152  (% class="box infomessage" id="HCaution:" %)