Skip to Content

Changes for page Zūm Discovery

Last modified by Alexander Mott on 2025/04/03 17:35
From version 32.1
edited by Craig Lewis
on 2024/09/30 17:35
Change comment: There is no comment for this version
To version 24.1
edited by Alexander Mott
on 2024/01/05 18:49
Change comment: Renamed back-links.

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.craig\.lewis@chiefintegrations\.com
1 +XWiki.alexander\.mott@chiefintegrations\.com
Content
... ... @@ -28,10 +28,8 @@
28 28  (((
29 29  * ShowRunnerCLC™ version 3.014 or newer required
30 30  * Zūm Wired firmware .puf version 1.02.10 or greater required (ZUMNET-JBOX installed minimum version 1.001.00081)
31 -* Disconnect from any ZUMNET devices you may be connected to in Toolbox and confirm all hardware (NETs and LINKs) are online prior to running the discovery commands
31 +* Disconnect from any ZUMNET devices you may be connected to in Toolbox prior to running the discovery commands
32 32  * Cresnet devices landed on Zūm Link will not be discovered (Crestron bug expected to be corrected in a future firmware release)
33 -* ZUMLINK-IOs will not be discovered (Expected to be discoverable in future ShowRunnerCLC™ release)
34 -* ZUMLINK-KPs will not be discovered on older versions of ShowRunnerCLC™ (v3.058 or newer will discover keypads and set as remote type)
35 35  * One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
36 36  )))
37 37  
... ... @@ -48,13 +48,7 @@
48 48  1*. Load the Zūm Wired firmware to the ZUMNET-JBOX
49 49  1*. Repeat the above steps for all ZUMNET-JBOXs
50 50  1*. Once all the ZUMNET-JBOXs have pushed the new firmware to their hosted devices, disconnect from them in Toolbox and proceed to the next step
51 -1. Connect to each ZUMNET-JBOX in the Crestron Zūm App
52 -1*. Commission room through the app
53 -1**. configure keypad logic
54 -1**. configure occupancy sensor settings
55 -1**. calibrate photocell(s)
56 -1*. Set hostnames for the ZUMNETs.
57 -1**. Zūm discovery will bring in hostnames.
49 +1. Connect to first ZUMNET-JBOX in the Crestron Zūm App
58 58  1. Unique Connection IDs should be automatically assigned to any Zūm Link and Cresnet devices on the ZUMNET-JBOX
59 59  1*. If firmware was out-of-date, then this step should have already been completed
60 60  1*. If unique CIDs are not automatically assigned, connect to the JBOX in Toolbox and give the devices unique CIDs
... ... @@ -88,7 +88,6 @@
88 88  * ShowRunnerCLC™ will automatically address any ZUM-NETBRIDGES that do not need have addresses assigned, but will still honor any already addressed devices
89 89  * Disconnect from any RF gateways you may be connected to in Toolbox prior to running the discovery command
90 90  * Plug loads will not appear in the ShowRunnerCLC™ UI
91 -* Newer GWEXER firmware enables SSL by default. Follow the instructions at [[SSL User Configuration>>doc:SHOWRUNNER™ User Guide & Wiki.SHOWRUNNER™ Appendix.SSL User Configuration.WebHome]] and manually add the IP Table entries on the GWEXER
92 92  )))
93 93  
94 94  (% class="box infomessage" id="HCaution:" %)