Skip to Content

Changes for page Zūm Discovery

Last modified by Alexander Mott on 2025/04/03 17:35
From version 26.1
edited by Craig Lewis
on 2024/05/29 15:37
Change comment: There is no comment for this version
To version 23.2
edited by Alexander Mott
on 2023/12/13 19:15
Change comment: Update document after refactoring.

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.craig\.lewis@chiefintegrations\.com
1 +XWiki.alexander\.mott@chiefintegrations\.com
Content
... ... @@ -8,7 +8,7 @@
8 8  
9 9  (% class="box warningmessage" %)
10 10  (((
11 -This article is about automatically building a ShowRunnerCLC™ configuration using the Zūm Discovery feature of ShowRunnerCLC™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Zūm App Overview.WebHome]].
11 +This article is about automatically building a ShowRunnerCLC™ configuration using the Zūm Discovery feature of ShowRunnerCLC™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
12 12  For instructions on configuring Zūm Net devices using Crestron Toolbox, see [[this page>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.ZUMNET-JBOX Setup.WebHome]].
13 13  )))
14 14  
... ... @@ -30,7 +30,6 @@
30 30  * Zūm Wired firmware .puf version 1.02.10 or greater required (ZUMNET-JBOX installed minimum version 1.001.00081)
31 31  * Disconnect from any ZUMNET devices you may be connected to in Toolbox prior to running the discovery commands
32 32  * Cresnet devices landed on Zūm Link will not be discovered (Crestron bug expected to be corrected in a future firmware release)
33 -* ZUMLINK-KPs will not be discovered (Expected to be discoverable in future release)
34 34  * One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
35 35  )))
36 36  
... ... @@ -47,13 +47,7 @@
47 47  1*. Load the Zūm Wired firmware to the ZUMNET-JBOX
48 48  1*. Repeat the above steps for all ZUMNET-JBOXs
49 49  1*. Once all the ZUMNET-JBOXs have pushed the new firmware to their hosted devices, disconnect from them in Toolbox and proceed to the next step
50 -1. Connect to each ZUMNET-JBOX in the Crestron Zūm App
51 -1*. Commission room through the app
52 -1**. configure keypad logic
53 -1**. configure occupancy sensor settings
54 -1**. calibrate photocell(s)
55 -1*. Set hostnames for the ZUMNETs.
56 -1**. Zūm discovery will bring in hostnames.
49 +1. Connect to first ZUMNET-JBOX in the Crestron Zūm App
57 57  1. Unique Connection IDs should be automatically assigned to any Zūm Link and Cresnet devices on the ZUMNET-JBOX
58 58  1*. If firmware was out-of-date, then this step should have already been completed
59 59  1*. If unique CIDs are not automatically assigned, connect to the JBOX in Toolbox and give the devices unique CIDs