Skip to Content

Changes for page Zūm Discovery

Last modified by Alexander Mott on 2025/04/03 17:35
From version 20.1
edited by Alexander Mott
on 2023/10/11 16:36
Change comment: There is no comment for this version
To version 9.1
edited by Alexander Mott
on 2022/10/05 16:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,18 +13,6 @@
1 -(% class="box errormessage" %)
2 -(((
3 -WARNING: Cresnet Discovery is not currently working on ZUMNET-JBOXs. Crestron has acknowledged a fix has been sent to QE.
4 -
5 -Downgrade ShowRunnerCLC™ to v3.018 in order to auto-discover hardware. ShowRunnerCLC™ can be subsequently upgraded once discovery is complete.
6 -)))
7 -
8 -(% class="box errormessage" %)
9 -(((
10 -IMPORTANT: When using ShowRunnerCLC™ with a ZUM-HUB4, do not discover Zūm Rooms using the Crestron HUB4 Web UI. During discovery, the HUB4 will claim ZUMNET-JBOXs and prevent ShowRunnerCLC™ from auto-discovering or registering the Zūm hardware for itself.
11 -)))
12 -
13 13  (% class="box warningmessage" %)
14 14  (((
15 -This article is about automatically building a ShowRunnerCLC™ configuration using the Zūm Discovery feature of ShowRunnerCLC™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
3 +This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Discovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
16 16  For instructions on configuring Zūm Net devices using Crestron Toolbox, see [[this page>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.ZUMNET-JBOX Setup.WebHome]].
17 17  )))
18 18  
... ... @@ -20,18 +20,20 @@
20 20  {{toc/}}
21 21  {{/box}}
22 22  
23 -If Zūm Wired or Wireless devices have been configured using Crestron's Zūm App, then it is possible to automatically build a ShowRunnerCLC™ configuration file using the Zūm Discovery feature that is built into ShowRunnerCLC™.
11 +(% class="row" %)
12 +(((
13 +If Zūm Wired or Wireless devices have been configured using Crestron's Zūm App, then it is possible to automatically build a SHOWRUNNER™ configuration file using the Zūm Discovery feature that is built into SHOWRUNNER™.
24 24  
25 -There are certain pre-requisites and limitations when building a ShowRunnerCLC™ configuration this way, and it may sometimes be necessary make some adjustments to the final configuration, such as changing keypad types and moving loads between areas.
15 +There are certain pre-requisites and limitations when building a SHOWRUNNER™ configuration this way, and it may sometimes be necessary make some adjustments to the final configuration, such as changing keypad types and moving loads between areas.
26 26  
27 27  = Zūm Wired Discovery =
28 28  
29 29  == Notes and Limitations ==
30 30  
31 -(% class="box warningmessage" %)
21 +(% class="box errormessage" %)
32 32  (((
33 -* ShowRunnerCLC™ version 3.014 or newer required
34 -* Zūm Wired firmware .puf version 1.02.10 or greater required (ZUMNET-JBOX installed minimum version 1.001.00081)
23 +* SHOWRUNNER™ version 3.014 or newer required
24 +* Zūm Wired firmware version 1.02.10 or greater required
35 35  * Disconnect from any ZUMNET devices you may be connected to in Toolbox prior to running the discovery commands
36 36  * Cresnet devices landed on Zūm Link will not be discovered (Crestron bug expected to be corrected in a future firmware release)
37 37  * One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
... ... @@ -39,13 +39,13 @@
39 39  
40 40  == Steps ==
41 41  
42 -1. [[Install ShowRunner™>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.WebHome]] on the processor and configure the processor as necessary
32 +1. [[Install SHOWRUNNER™>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.WebHome]] on the processor and configure the processor as necessary
43 43  1*. Note that while Zūm Wired discovery will build a configuration, if a configuration file was provided then it should still be loaded as it may contain location data or non-Zūm devices.
44 44  1. If the ZUMNET-JBOX firmware is too out-of-date to connect using the Crestron Zūm App, then there are some additional steps required: 
45 45  1*. Connect to the first ZUMNET-JBOX in Toolbox
46 46  1*. Configure a static IP address for the ZUMNET-JBOX if there is no DHCP server on the network 
47 -1**. Note: The ShowRunnerCLC™ built-in DHCP server is not meant to be used in production
48 -1**. If the ShowRunnerCLC™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
37 +1**. Note: The SHOWRUNNER™ built-in DHCP server is not meant to be used in production
38 +1**. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
49 49  1*. Set unique Connection IDs for each device hosted on the ZUMNET-JBOX so that their firmware can be updated
50 50  1*. Load the Zūm Wired firmware to the ZUMNET-JBOX
51 51  1*. Repeat the above steps for all ZUMNET-JBOXs
... ... @@ -56,70 +56,72 @@
56 56  1*. If unique CIDs are not automatically assigned, connect to the JBOX in Toolbox and give the devices unique CIDs
57 57  1. Configure a static IP address for the ZUMNET-JBOX if there is no DHCP server on the network 
58 58  1*. If firmware was out-of-date, then this step should have already been completed
59 -1*. Note: The ShowRunnerCLC™ built-in DHCP server is not meant to be used in production
60 -1*. If the ShowRunnerCLC™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
49 +1*. Note: The SHOWRUNNER™ built-in DHCP server is not meant to be used in production
50 +1*. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
61 61  1. Optionally, manually configure the ZUMNET-JBOX IP table to point at the processor if you want to keep track of which ZUMNET-JBOX is at each IP-ID
62 62  1*. If you do not manually configure the IP table, then SHOWRUNNER™ will automatically configure the IP-ID for each ZUMNET-JBOX during discovery
63 -1. Set the ZUMNET-JBOX into either Zūm ("App") mode or CNET mode as required for the program
64 -1*. Full control from ShowRunnerCLC™ is only possible if all ZUMNET-JBOXs are in CNET mode. Odd behavior may result from conflicts between ShowRunnerCLC™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
65 -1. Repeat from step 3 until all ZUMNET-JBOXs that are to be controlled by ShowRunnerCLC™ have static IP addresses and unique CIDs for any hosted devices
53 +1. Repeat from step 3 until all ZUMNET-JBOXs that are to be controlled by SHOWRUNNER™ have static IP addresses and unique CIDs for any hosted devices
66 66  1. Disconnect from any ZUMNET-JBOXs and then connect to the processor in Toolbox
67 67  1. Run the command: ##sr discover zumnet true false##
68 -1*. This command tells ShowRunnerCLC™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding IP Devices to the configuration
56 +1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding areas and loads to the configuration
57 +1*. One area will be created per ZUMNET-JBOX
69 69  1. Run the command: ##sr discover zumnet true true##
70 -1*. This command tells ShowRunnerCLC™ to discover all Zūm Link hardware (including the internal ZUMNET-JBOX load controller) on the previously discovered Zūm Net devices and then add corresponding areas, loads, sensors, etc. to the configuration
71 -1**. One area will be created per ZUMNET-JBOX, and all hardware attached to that ZUMNET-JBOX will be assigned to that area
59 +1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware on the previously discovered Zūm Net devices
72 72  1*. This command **does not** bring in Cresnet devices: those must be added to the configuration manually until this issue is fixed in the Zūm Wired firmware
73 -1. If all steps have been performed successfully, then you should be able to use the ##sr show area##, ##sr show load##, ##sr show keypad##, and ##sr show occ## commands to see that the ZUMNET and ZUMLINK hardware has been discovered correctly.
61 +1. Put all ZUMNET-JBOXs into CNET mode in order to allow full control from SHOWRUNNER™
62 +1*. Odd behavior may result from conflicts between SHOWRUNNER™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
74 74  
75 75  = Zūm Wireless Discovery =
76 76  
77 77  == Notes and Limitations ==
67 +)))
78 78  
79 -(% class="box warningmessage" %)
69 +(% class="box errormessage" %)
80 80  (((
81 -* Processor with ShowRunnerCLC™ version 2.190 or newer must be running on the same network as the gateway(s) to be acquired
82 -** For ShowRunnerCLC™ versions prior to 3.014 and newer, replace **##sr discover zummesh##** commands with **##sr discover zum##**
71 +* Processor with SHOWRUNNER™ version 2.190 or newer must be running on the same network as the gateway(s) to be acquired
72 +** For SHOWRUNNER™ versions prior to 3.014 and newer, replace **##sr discover zummesh##** commands with **##sr discover zum##**
83 83  * ZUM-NETBRIDGES must already be acquired to their respective gateway
84 -* ShowRunnerCLC™ will automatically address any ZUM-NETBRIDGES that do not need have addresses assigned, but will still honor any already addressed devices
74 +* SHOWRUNNER™ will automatically address any ZUM-NETBRIDGES that do not need have addresses assigned, but will still honor any already addressed devices
85 85  * Disconnect from any RF gateways you may be connected to in Toolbox prior to running the discovery command
86 -* Plug loads will not appear in the ShowRunnerCLC™ UI
76 +* Plug loads will not appear in the SHOWRUNNER™ UI
87 87  )))
88 88  
89 -(% class="box infomessage" id="HCaution:" %)
79 +(% class="box warningmessage" id="HCaution:" %)
90 90  (((
91 -**Note:** ShowRunnerCLC™ has two different approaches for Zūm Wireless Discovery
81 +**Note:** SHOWRUNNER™ has two different approaches for Zūm Wireless Discovery
92 92  
93 -1. **Manual RF Gateway Assignment** - ShowRunnerCLC™ can be told which gateways it should scan. Use this approach if you have gateways that are used by multiple systems on the same local network.
94 -1. **Claim All RF Gateways** - ShowRunnerCLC™ will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own. **DO NOT** use this method if there are gateways used by different ShowRunnerCLC™ or other Crestron systems on the same local network.
83 +1. **Manual RF Gateway Assignment** - SHOWRUNNER™ can be told which gateways it should scan. Use this approach if you have gateways that are used by multiple systems on the same local network.
84 +1. **Claim All RF Gateways** - SHOWRUNNER™ will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own. **DO NOT** use this method if there are gateways used by different SHOWRUNNER™ or other Crestron systems on the same local network.
95 95  )))
96 96  
87 +(% class="row" %)
88 +(((
97 97  == Manual RF Gateway Assignment Instructions ==
98 98  
99 -Use this method if you have multiple ShowRunnerCLC™ instances on the same network or have gateways used by other Crestron systems.
91 +Use this method if you have multiple SHOWRUNNER™ instances on the same network or have gateways used by other Crestron systems.
100 100  
101 101  * Connect to the processor's console with Toolbox or your favorite SSH client.
102 102  * Type ##sr devmgr ethernet query## and press enter. This queries the local network for RF Gateways.
103 103  * Type ##sr devmgr ethernet show devices## and press enter. This displays all found Crestron ethernet devices.
104 -* For each gateway that you'd like this instance of SHOWRUNNER™ to use, use the hostname from the table of found ethernet devices. For example if the gateway Hostname is CEN-GWEXER-9E6ADA type ##sr ethernet device claim CEN-GWEXER-9E6ADA##. ShowRunnerCLC™ will auto-assign an IP-ID. After all gateways have been claimed by ShowRunnerCLC™, proceed to the next step.
96 +* For each gateway that you'd like this instance of SHOWRUNNER™ to use, use the hostname from the table of found ethernet devices. For example if the gateway Hostname is CEN-GWEXER-9E6ADA type ##sr ethernet device claim CEN-GWEXER-9E6ADA##. SHOWRUNNER™ will auto-assign an IP-ID. After all gateways have been claimed by SHOWRUNNER™, proceed to the next step.
105 105  * Type ##sr discover zummesh false## and press enter.
106 106  * Status messages and the results will be displayed on the console. The process should take about 3 minutes.
107 -* When the discovery is finished type ##sr save## and press enter to save the updated config. Due to an unknown quirk that we are looking into, ShowRunnerCLC™ must be restarted to complete the acquire process.
108 -* Type ##progreset## and press enter to restart ShowRunnerCLC™
109 -* Once SHOWRUNNER™ has finished restarting type ##sr discover zummesh false## and press enter. ShowRunnerCLC™ will be able to acquire the loads attached to the Zūm rooms at this point.
99 +* When the discovery is finished type ##sr save## and press enter to save the updated config. Due to an unknown quirk that we are looking into, SHOWRUNNER™ must be restarted to complete the acquire process.
100 +* Type ##progreset## and press enter to restart SHOWRUNNER™
101 +* Once SHOWRUNNER™ has finished restarting type ##sr discover zummesh false## and press enter. SHOWRUNNER™ will be able to acquire the loads attached to the Zūm rooms at this point.
110 110  * Once completed SHOWRUNNER™ is now ready for full Zūm control
111 111  
112 112  == Claim All RF Gateways Instructions ==
113 113  
114 -Use this method when you have a single ShowRunnerCLC™ instance on a local network with all gateways being used for ShowRunnerCLC™.
106 +Use this method when you have a single SHOWRUNNER™ instance on a local network with all gateways being used for SHOWRUNNER™.
115 115  
116 116  * Connect to the processor's console with Toolbox or your favorite SSH client.
117 117  * Type ##sr discover zummesh true## and press enter.
118 118  * Status messages and the results will be displayed on the console. The process should take about 3 minutes.
119 -* When the discovery is finished type ##sr save## and press enter to save the updated config. Due to an unknown quirk that we are looking into, ShowRunnerCLC™ must be restarted to complete the acquire process.
120 -* Type ##progreset## and press enter to restart ShowRunnerCLC™
121 -* Once ShowRunnerCLC™ has finished restarting type ##sr discover zummesh false## and press enter. ShowRunnerCLC™ will be able to acquire the loads attached to the Zūm rooms at this point.
122 -* Once completed ShowRunnerCLC™ is now ready for full Zūm control
111 +* When the discovery is finished type ##sr save## and press enter to save the updated config. Due to an unknown quirk that we are looking into, SHOWRUNNER™ must be restarted to complete the acquire process.
112 +* Type ##progreset## and press enter to restart SHOWRUNNER™
113 +* Once SHOWRUNNER™ has finished restarting type ##sr discover zummesh false## and press enter. SHOWRUNNER™ will be able to acquire the loads attached to the Zūm rooms at this point.
114 +* Once completed SHOWRUNNER™ is now ready for full Zūm control
123 123  
124 124  == Examples ==
125 125  
... ... @@ -315,3 +315,4 @@
315 315  Removed Loads: 0
316 316  Zum Discovery Finished
317 317  }}}
310 +)))