Skip to Content

Changes for page Zūm Discovery

Last modified by Alexander Mott on 2025/04/03 17:35
From version 16.2
edited by Alexander Mott
on 2023/03/29 21:28
Change comment: There is no comment for this version
To version 13.1
edited by Alexander Mott
on 2022/10/10 23:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,8 +6,3 @@
1 -(% class="box errormessage" %)
2 -(((
3 -WARNING: Cresnet Discovery is not currently working on ZUMNET-JBOXs. Crestron has acknowledged a fix has been sent to QE. Discovery must be fixed before SHOWRUNNER™ can auto-discover hardware.
4 -)))
5 -
6 6  (% class="box warningmessage" %)
7 7  (((
8 8  This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Discovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
... ... @@ -21,7 +21,7 @@
21 21  
22 22  == Notes and Limitations ==
23 23  
24 -(% class="box warningmessage" %)
19 +(% class="box errormessage" %)
25 25  (((
26 26  * SHOWRUNNER™ version 3.014 or newer required
27 27  * Zūm Wired firmware .puf version 1.02.10 or greater required (ZUMNET-JBOX installed minimum version 1.001.00081)
... ... @@ -63,13 +63,12 @@
63 63  1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware (including the internal ZUMNET-JBOX load controller) on the previously discovered Zūm Net devices and then add corresponding areas, loads, sensors, etc. to the configuration
64 64  1**. One area will be created per ZUMNET-JBOX, and all hardware attached to that ZUMNET-JBOX will be assigned to that area
65 65  1*. This command **does not** bring in Cresnet devices: those must be added to the configuration manually until this issue is fixed in the Zūm Wired firmware
66 -1. If all steps have been performed successfully, then you should be able to use the ##sr show area##, ##sr show load##, ##sr show keypad##, and ##sr show occ## commands to see that the ZUMNET and ZUMLINK hardware has been discovered correctly.
67 67  
68 68  = Zūm Wireless Discovery =
69 69  
70 70  == Notes and Limitations ==
71 71  
72 -(% class="box warningmessage" %)
66 +(% class="box errormessage" %)
73 73  (((
74 74  * Processor with SHOWRUNNER™ version 2.190 or newer must be running on the same network as the gateway(s) to be acquired
75 75  ** For SHOWRUNNER™ versions prior to 3.014 and newer, replace **##sr discover zummesh##** commands with **##sr discover zum##**
... ... @@ -79,7 +79,7 @@
79 79  * Plug loads will not appear in the SHOWRUNNER™ UI
80 80  )))
81 81  
82 -(% class="box infomessage" id="HCaution:" %)
76 +(% class="box warningmessage" id="HCaution:" %)
83 83  (((
84 84  **Note:** SHOWRUNNER™ has two different approaches for Zūm Wireless Discovery
85 85