Skip to Content

Changes for page Zūm Discovery

Last modified by Alexander Mott on 2025/04/03 17:35
From version 16.1
edited by Alexander Mott
on 2023/03/29 21:19
Change comment: There is no comment for this version
To version 9.1
edited by Alexander Mott
on 2022/10/05 16:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,8 +6,3 @@
1 -(% class="box errormessage" %)
2 -(((
3 -WARNING: Cresnet Discovery is not currently working on ZUMNET-JBOXs. Crestron has acknowledged a fix has been sent to QE. Discovery must be fixed before SHOWRUNNER™ can auto-discover hardware.
4 -)))
5 -
6 6  (% class="box warningmessage" %)
7 7  (((
8 8  This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Discovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
... ... @@ -13,6 +13,8 @@
13 13  {{toc/}}
14 14  {{/box}}
15 15  
11 +(% class="row" %)
12 +(((
16 16  If Zūm Wired or Wireless devices have been configured using Crestron's Zūm App, then it is possible to automatically build a SHOWRUNNER™ configuration file using the Zūm Discovery feature that is built into SHOWRUNNER™.
17 17  
18 18  There are certain pre-requisites and limitations when building a SHOWRUNNER™ configuration this way, and it may sometimes be necessary make some adjustments to the final configuration, such as changing keypad types and moving loads between areas.
... ... @@ -21,10 +21,10 @@
21 21  
22 22  == Notes and Limitations ==
23 23  
24 -(% class="box warningmessage" %)
21 +(% class="box errormessage" %)
25 25  (((
26 26  * SHOWRUNNER™ version 3.014 or newer required
27 -* Zūm Wired firmware .puf version 1.02.10 or greater required (ZUMNET-JBOX installed minimum version 1.001.00081)
24 +* Zūm Wired firmware version 1.02.10 or greater required
28 28  * Disconnect from any ZUMNET devices you may be connected to in Toolbox prior to running the discovery commands
29 29  * Cresnet devices landed on Zūm Link will not be discovered (Crestron bug expected to be corrected in a future firmware release)
30 30  * One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
... ... @@ -53,21 +53,21 @@
53 53  1*. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
54 54  1. Optionally, manually configure the ZUMNET-JBOX IP table to point at the processor if you want to keep track of which ZUMNET-JBOX is at each IP-ID
55 55  1*. If you do not manually configure the IP table, then SHOWRUNNER™ will automatically configure the IP-ID for each ZUMNET-JBOX during discovery
56 -1. Set the ZUMNET-JBOX into either Zūm ("App") mode or CNET mode as required for the program
57 -1*. Full control from SHOWRUNNER™ is only possible if all ZUMNET-JBOXs are in CNET mode. Odd behavior may result from conflicts between SHOWRUNNER™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
58 58  1. Repeat from step 3 until all ZUMNET-JBOXs that are to be controlled by SHOWRUNNER™ have static IP addresses and unique CIDs for any hosted devices
59 59  1. Disconnect from any ZUMNET-JBOXs and then connect to the processor in Toolbox
60 60  1. Run the command: ##sr discover zumnet true false##
61 -1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding IP Devices to the configuration
56 +1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding areas and loads to the configuration
57 +1*. One area will be created per ZUMNET-JBOX
62 62  1. Run the command: ##sr discover zumnet true true##
63 -1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware (including the internal ZUMNET-JBOX load controller) on the previously discovered Zūm Net devices and then add corresponding areas, loads, sensors, etc. to the configuration
64 -1**. One area will be created per ZUMNET-JBOX, and all hardware attached to that ZUMNET-JBOX will be assigned to that area
59 +1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware on the previously discovered Zūm Net devices
65 65  1*. This command **does not** bring in Cresnet devices: those must be added to the configuration manually until this issue is fixed in the Zūm Wired firmware
66 -1. If all steps have been performed successfully, then you should be able to use the ##sr show area##, ##sr show load##, ##sr show keypad##, and ##sr show occ## commands to see that the ZUMNET and ZUMLINK hardware has been discovered correctly.
61 +1. Put all ZUMNET-JBOXs into CNET mode in order to allow full control from SHOWRUNNER™
62 +1*. Odd behavior may result from conflicts between SHOWRUNNER™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
67 67  
68 68  = Zūm Wireless Discovery =
69 69  
70 70  == Notes and Limitations ==
67 +)))
71 71  
72 72  (% class="box errormessage" %)
73 73  (((
... ... @@ -87,6 +87,8 @@
87 87  1. **Claim All RF Gateways** - SHOWRUNNER™ will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own. **DO NOT** use this method if there are gateways used by different SHOWRUNNER™ or other Crestron systems on the same local network.
88 88  )))
89 89  
87 +(% class="row" %)
88 +(((
90 90  == Manual RF Gateway Assignment Instructions ==
91 91  
92 92  Use this method if you have multiple SHOWRUNNER™ instances on the same network or have gateways used by other Crestron systems.
... ... @@ -308,3 +308,4 @@
308 308  Removed Loads: 0
309 309  Zum Discovery Finished
310 310  }}}
310 +)))