Skip to Content

Changes for page Zūm Discovery

Last modified by Austin Weygandt on 2025/05/02 20:21
From version 14.1
edited by Alexander Mott
on 2022/10/10 23:35
Change comment: There is no comment for this version
To version 3.1
edited by Alexander Mott
on 2022/09/22 21:47
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -Zūm Discovery
1 +Zūm Autodiscovery
Content
... ... @@ -1,6 +1,6 @@
1 1  (% class="box warningmessage" %)
2 2  (((
3 -This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Discovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
3 +This article is about automatically building a SHOWRUNNER™ configuration using the Zūm Autodiscovery feature of SHOWRUNNER™. For instructions on configuring Zūm Wired rooms using the Crestron Zūm App, see [[this page>>SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Crestron Zūm App Overview.WebHome]].
4 4  For instructions on configuring Zūm Net devices using Crestron Toolbox, see [[this page>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.ZUMNET-JBOX Setup.WebHome]].
5 5  )))
6 6  
... ... @@ -8,131 +8,72 @@
8 8  {{toc/}}
9 9  {{/box}}
10 10  
11 -If Zūm Wired or Wireless devices have been configured using Crestron's Zūm App, then it is possible to automatically build a SHOWRUNNER™ configuration file using the Zūm Discovery feature that is built into SHOWRUNNER™.
11 +(% class="row" %)
12 +(((
13 +If Zūm Net devices have been configured using Crestron's Zūm App
12 12  
13 -There are certain pre-requisites and limitations when building a SHOWRUNNER™ configuration this way, and it may sometimes be necessary make some adjustments to the final configuration, such as changing keypad types and moving loads between areas.
15 += Zūm Wired =
14 14  
15 -= Zūm Wired Discovery =
17 +Lorem
16 16  
17 -== Notes and Limitations ==
19 += Zūm Wireless =
18 18  
19 -(% class="box errormessage" %)
20 -(((
21 -* SHOWRUNNER™ version 3.014 or newer required
22 -* Zūm Wired firmware .puf version 1.02.10 or greater required (ZUMNET-JBOX installed minimum version 1.001.00081)
23 -* Disconnect from any ZUMNET devices you may be connected to in Toolbox prior to running the discovery commands
24 -* Cresnet devices landed on Zūm Link will not be discovered (Crestron bug expected to be corrected in a future firmware release)
25 -* One area will be created per ZUMNET-JBOX; if there are more areas than ZUMNET-JBOXs, additional areas must be created manually
26 -)))
27 27  
28 -== Steps ==
22 +As of version 2.190 ShowRunner can discover RF Gateways and attached Zum NETBRIDGES. ShowRunner will find all devices, set them up, create areas and loads.
23 +*Disconnect from the gateway before discovery as they cannot support multiple connections*
24 +*Plug loads do not appear in the UI*
29 29  
30 -1. [[Install SHOWRUNNER™>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.WebHome]] on the processor and configure the processor as necessary
31 -1*. Note that while Zūm Wired discovery will build a configuration, if a configuration file was provided then it should still be loaded as it may contain location data or non-Zūm devices.
32 -1. If the ZUMNET-JBOX firmware is too out-of-date to connect using the Crestron Zūm App, then there are some additional steps required: 
33 -1*. Connect to the first ZUMNET-JBOX in Toolbox
34 -1*. Configure a static IP address for the ZUMNET-JBOX if there is no DHCP server on the network 
35 -1**. Note: The SHOWRUNNER™ built-in DHCP server is not meant to be used in production
36 -1**. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
37 -1*. Set unique Connection IDs for each device hosted on the ZUMNET-JBOX so that their firmware can be updated
38 -1*. Load the Zūm Wired firmware to the ZUMNET-JBOX
39 -1*. Repeat the above steps for all ZUMNET-JBOXs
40 -1*. Once all the ZUMNET-JBOXs have pushed the new firmware to their hosted devices, disconnect from them in Toolbox and proceed to the next step
41 -1. Connect to first ZUMNET-JBOX in the Crestron Zūm App
42 -1. Unique Connection IDs should be automatically assigned to any Zūm Link and Cresnet devices on the ZUMNET-JBOX
43 -1*. If firmware was out-of-date, then this step should have already been completed
44 -1*. If unique CIDs are not automatically assigned, connect to the JBOX in Toolbox and give the devices unique CIDs
45 -1. Configure a static IP address for the ZUMNET-JBOX if there is no DHCP server on the network 
46 -1*. If firmware was out-of-date, then this step should have already been completed
47 -1*. Note: The SHOWRUNNER™ built-in DHCP server is not meant to be used in production
48 -1*. If the SHOWRUNNER™ built-in DHCP server was used to assign IP addresses to devices, it is still necessary to give those devices static IP addresses
49 -1. Optionally, manually configure the ZUMNET-JBOX IP table to point at the processor if you want to keep track of which ZUMNET-JBOX is at each IP-ID
50 -1*. If you do not manually configure the IP table, then SHOWRUNNER™ will automatically configure the IP-ID for each ZUMNET-JBOX during discovery
51 -1. Set the ZUMNET-JBOX into either Zūm ("App") mode or CNET mode as required for the program
52 -1*. Full control from SHOWRUNNER™ is only possible if all ZUMNET-JBOXs are in CNET mode. Odd behavior may result from conflicts between SHOWRUNNER™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
53 -1. Repeat from step 3 until all ZUMNET-JBOXs that are to be controlled by SHOWRUNNER™ have static IP addresses and unique CIDs for any hosted devices
54 -1. Disconnect from any ZUMNET-JBOXs and then connect to the processor in Toolbox
55 -1. Run the command: ##sr discover zumnet true false##
56 -1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding IP Devices to the configuration
57 -1. Run the command: ##sr discover zumnet true true##
58 -1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware (including the internal ZUMNET-JBOX load controller) on the previously discovered Zūm Net devices and then add corresponding areas, loads, sensors, etc. to the configuration
59 -1**. One area will be created per ZUMNET-JBOX, and all hardware attached to that ZUMNET-JBOX will be assigned to that area
60 -1*. This command **does not** bring in Cresnet devices: those must be added to the configuration manually until this issue is fixed in the Zūm Wired firmware
61 -1. If all steps have been performed successfully, then you should be able to use the ##sr show area##, ##sr show load##, ##sr show keypad##, and ##sr show occ## commands to see that the ZUMNET and ZUMLINK hardware has been discovered correctly.
26 +== Pre-Requisites: ==
62 62  
63 -= Zūm Wireless Discovery =
28 +* Zum NETBRIDGES acquired to their respective gateway (CEN-GWEXER/ZUMNET-GATEWAY)
29 +* ShowRunner installed and running on a 3-series processor on the same network as the gateway
30 +* NETBRIDGES do not need to have addresses assigned. ShowRunner will automatically address them. If devices all already addressed then their addresses will be honored.
64 64  
65 -== Notes and Limitations ==
66 -
67 -(% class="box errormessage" %)
68 -(((
69 -* Processor with SHOWRUNNER™ version 2.190 or newer must be running on the same network as the gateway(s) to be acquired
70 -** For SHOWRUNNER™ versions prior to 3.014 and newer, replace **##sr discover zummesh##** commands with **##sr discover zum##**
71 -* ZUM-NETBRIDGES must already be acquired to their respective gateway
72 -* SHOWRUNNER™ will automatically address any ZUM-NETBRIDGES that do not need have addresses assigned, but will still honor any already addressed devices
73 -* Disconnect from any RF gateways you may be connected to in Toolbox prior to running the discovery command
74 -* Plug loads will not appear in the SHOWRUNNER™ UI
75 -)))
76 -
77 77  (% class="box warningmessage" id="HCaution:" %)
78 78  (((
79 -**Note:** SHOWRUNNER™ has two different approaches for Zūm Wireless Discovery
80 -
81 -1. **Manual RF Gateway Assignment** - SHOWRUNNER™ can be told which gateways it should scan. Use this approach if you have gateways that are used by multiple systems on the same local network.
82 -1. **Claim All RF Gateways** - SHOWRUNNER™ will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own. **DO NOT** use this method if there are gateways used by different SHOWRUNNER™ or other Crestron systems on the same local network.
34 +**Note,** SHOWRUNNER has two different types of Zum Wireless autodiscovery:
35 +1. Claim All RF Gateways - ShowRunner will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own.  DO NOT use this method if there are gateways used by different ShowRunner or other Crestron systems on the same local network.
36 +1. Manual RF Gateway Assignment - ShowRunner can be told which gateways it should scan. Use this approach if you have gateways that are used by multiple systems on the same local network.
83 83  )))
84 84  
85 -== Manual RF Gateway Assignment Instructions ==
39 +== Option 1: Claim All Gateways: ==
86 86  
87 -Use this method if you have multiple SHOWRUNNER™ instances on the same network or have gateways used by other Crestron systems.
41 +Use this method when you have a single ShowRunner instance on a local network with all gateways being used for ShowRunner.
88 88  
89 89  * Connect to the processor's console with Toolbox or your favorite SSH client.
90 -* Type ##sr devmgr ethernet query## and press enter. This queries the local network for RF Gateways.
91 -* Type ##sr devmgr ethernet show devices## and press enter. This displays all found Crestron ethernet devices.
92 -* For each gateway that you'd like this instance of SHOWRUNNER™ to use, use the hostname from the table of found ethernet devices. For example if the gateway Hostname is CEN-GWEXER-9E6ADA type ##sr ethernet device claim CEN-GWEXER-9E6ADA##. SHOWRUNNER™ will auto-assign an IP-ID. After all gateways have been claimed by SHOWRUNNER™, proceed to the next step.
93 -* Type ##sr discover zummesh false## and press enter.
94 -* Status messages and the results will be displayed on the console. The process should take about 3 minutes.
95 -* When the discovery is finished type ##sr save## and press enter to save the updated config. Due to an unknown quirk that we are looking into, SHOWRUNNER™ must be restarted to complete the acquire process.
96 -* Type ##progreset## and press enter to restart SHOWRUNNER™
97 -* Once SHOWRUNNER™ has finished restarting type ##sr discover zummesh false## and press enter. SHOWRUNNER™ will be able to acquire the loads attached to the Zūm rooms at this point.
98 -* Once completed SHOWRUNNER™ is now ready for full Zūm control
44 +* Type "//sr discover zum true//" and press enter.
45 +* Status messages and the results will be displayed on the console. The process should take about 3 minutes.
46 +* When the discovery is finished type "//sr save//" and press enter to save the updated config. Due to an unknown quirk that we are looking into, ShowRunner must be restarted to complete the acquire process.
47 +* Type "//progreset//" and press enter to restart ShowRunner
48 +* Once ShowRunner has finished restarting type "//sr discover zum false//" and press enter. ShowRunner will be able to acquire the loads attached to the Zum rooms at this point.
49 +* Once completed ShowRunner is now ready for full Zum control
99 99  
100 -== Claim All RF Gateways Instructions ==
51 +== Option 2: Manual RF Gateway Claiming: ==
101 101  
102 -Use this method when you have a single SHOWRUNNER™ instance on a local network with all gateways being used for SHOWRUNNER™.
53 +Use this method if you have multiple ShowRunner instances on the same network or have gateways used by other Crestron systems.
103 103  
104 104  * Connect to the processor's console with Toolbox or your favorite SSH client.
105 -* Type ##sr discover zummesh true## and press enter.
106 -* Status messages and the results will be displayed on the console. The process should take about 3 minutes.
107 -* When the discovery is finished type ##sr save## and press enter to save the updated config. Due to an unknown quirk that we are looking into, SHOWRUNNER™ must be restarted to complete the acquire process.
108 -* Type ##progreset## and press enter to restart SHOWRUNNER™
109 -* Once SHOWRUNNER™ has finished restarting type ##sr discover zummesh false## and press enter. SHOWRUNNER™ will be able to acquire the loads attached to the Zūm rooms at this point.
110 -* Once completed SHOWRUNNER™ is now ready for full Zūm control
56 +* Type "//sr devmgr ethernet query//" and press enter. This queries the local network for RF Gateways.
57 +* Type "//sr devmgr ethernet show devices//" and press enter. This displays all found Crestron ethernet devices.
58 +* For each gateway that you'd like this instance of ShowRunner to use, use the hostname from the table of found ethernet devices. For example if the gateway Hostname is CEN-GWEXER-9E6ADA type "//sr ethernet device claim CEN-GWEXER-9E6ADA//". ShowRunner will auto-assign an IP-ID. After all gateways have been claimed by ShowRunner proceed to the next step.
59 +* Type "//sr discover zum false//" and press enter.
60 +* Status messages and the results will be displayed on the console. The process should take about 3 minutes.
61 +* When the discovery is finished type "//sr save//" and press enter to save the updated config. Due to an unknown quirk that we are looking into, ShowRunner must be restarted to complete the acquire process.
62 +* Type "//progreset//" and press enter to restart ShowRunner
63 +* Once ShowRunner has finished restarting type "//sr discover zum false//" and press enter. ShowRunner will be able to acquire the loads attached to the Zum rooms at this point.
64 +* Once completed ShowRunner is now ready for full Zum control
111 111  
112 112  == Examples ==
113 113  
114 -=== Manual Example ===
68 +=== Example for Option 1: ===
115 115  
116 -{{{MC4>sr devmgr ethernet query
117 -Ethrenet AutoDiscovery Result: AutoDiscoveryOperationSuccess
118 -MC4>sr devmgr ethernet show devices
119 -
120 -+--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
121 -| Adapter | Hostname | IP Address | IP-ID | ID |
122 -+--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
123 -| EthernetLANAdapter | CI-SJC-CEN-CI3-1-COM3 | 10.44.5.20 | 00 | CEN-CI3-1-C3COM-3 [v1.1620.00000, #008436E2] type:1 |
124 -+--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
125 -| EthernetLANAdapter | SB-DIN-CENCN-2 | 10.44.5.81 | 00 | DIN-CENCN-2-POE [v1.3544.00006, #8AB25AA3] |
126 -+--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
127 -| EthernetLANAdapter | CEN-GWEXER-9E6ADA | 10.44.5.120 | 00 | CEN-GWEXER [v1.4230.00015, #848210AD] |
128 -+--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
129 -
130 -MC4>sr ethernet device claim CEN-GWEXER-9E6ADA
131 -Claimed ethernet device: CEN-GWEXER-9E6ADA
132 -MC4>Update request from IP-ID-30 in Program 01
133 -MC4>sr discover zummesh false
134 -Starting Zum Discovery without gateway claiming
135 -MC4>Performing Discovery on 1 Gateways.
70 +{{{MC4>sr discover zum true
71 +Starting Zum Discovery with gateway claiming
72 +MC4>Found 1 Gateways to check.
73 +Claimed Gateway SN: 1720JBH04269 at IP-ID: 30
74 +Update request from IP-ID-30 in Program 01
75 +Claimed 1 Gateways. Waiting for queries to finish.
76 +Performing Discovery on 1 Gateways.
136 136  Evaluating 3 Devices on Gateway 30
137 137  Claiming ZUM-NETBRIDGE SN: 1726NEJ01096 from IP-ID: 30
138 138  Dev: ZUM-NETBRIDGE addrssing to RF ID: 03
... ... @@ -143,7 +143,6 @@
143 143  Claiming ZUM-NETBRIDGE SN: 1914NEJ03098 from IP-ID: 30
144 144  Dev: ZUM-NETBRIDGE addrssing to RF ID: 05
145 145  Setting up RF Device 'ZUM-NETBRIDGE' on Gateway 30 at RF-ID 05
146 -Querying cresnet
147 147  Discovering Zum Loads on 1 Gateways.
148 148  Discovering Zum Loads on 3 Devices.
149 149  NETBIRDGE: NewLoads: 0 ModifiedLoads: 0 RemovedLoads: 0
... ... @@ -163,7 +163,7 @@
163 163  MC4>progreset
164 164  ...
165 165  CI ShowRunner startup completed successfully in 8072ms
166 -MC4>sr discover zummesh false
106 +MC4>sr discover zum false
167 167  Starting Zum Discovery without gateway claiming
168 168  MC4>Notice: SimplSharpPro[App01] # 2020-07-21 22:19:46 # Recalling startup scenes (if applicable)
169 169  Performing Discovery on 1 Gateways.
... ... @@ -212,17 +212,31 @@
212 212  New Loads: 6
213 213  Modified Loads: 0
214 214  Removed Loads: 0
215 -Zum Discovery Finished}}}
155 +Zum Discovery Finished
156 +}}}
216 216  
217 -=== Claim All Example ===
158 +=== Example for Option 2: ===
218 218  
219 -{{{MC4>sr discover zummesh true
220 -Starting Zum Discovery with gateway claiming
221 -MC4>Found 1 Gateways to check.
222 -Claimed Gateway SN: 1720JBH04269 at IP-ID: 30
223 -Update request from IP-ID-30 in Program 01
224 -Claimed 1 Gateways. Waiting for queries to finish.
225 -Performing Discovery on 1 Gateways.
160 +{{{MC4>sr devmgr ethernet query
161 +Ethrenet AutoDiscovery Result: AutoDiscoveryOperationSuccess
162 +MC4>sr devmgr ethernet show devices
163 +
164 ++--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
165 +| Adapter | Hostname | IP Address | IP-ID | ID |
166 ++--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
167 +| EthernetLANAdapter | CI-SJC-CEN-CI3-1-COM3 | 10.44.5.20 | 00 | CEN-CI3-1-C3COM-3 [v1.1620.00000, #008436E2] type:1 |
168 ++--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
169 +| EthernetLANAdapter | SB-DIN-CENCN-2 | 10.44.5.81 | 00 | DIN-CENCN-2-POE [v1.3544.00006, #8AB25AA3] |
170 ++--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
171 +| EthernetLANAdapter | CEN-GWEXER-9E6ADA | 10.44.5.120 | 00 | CEN-GWEXER [v1.4230.00015, #848210AD] |
172 ++--------------------+-------------------------------+-------------+-------+----------------------------------------------------------------------------------+
173 +
174 +MC4>sr ethernet device claim CEN-GWEXER-9E6ADA
175 +Claimed ethernet device: CEN-GWEXER-9E6ADA
176 +MC4>Update request from IP-ID-30 in Program 01
177 +MC4>sr discover zum false
178 +Starting Zum Discovery without gateway claiming
179 +MC4>Performing Discovery on 1 Gateways.
226 226  Evaluating 3 Devices on Gateway 30
227 227  Claiming ZUM-NETBRIDGE SN: 1726NEJ01096 from IP-ID: 30
228 228  Dev: ZUM-NETBRIDGE addrssing to RF ID: 03
... ... @@ -233,6 +233,7 @@
233 233  Claiming ZUM-NETBRIDGE SN: 1914NEJ03098 from IP-ID: 30
234 234  Dev: ZUM-NETBRIDGE addrssing to RF ID: 05
235 235  Setting up RF Device 'ZUM-NETBRIDGE' on Gateway 30 at RF-ID 05
190 +Querying cresnet
236 236  Discovering Zum Loads on 1 Gateways.
237 237  Discovering Zum Loads on 3 Devices.
238 238  NETBIRDGE: NewLoads: 0 ModifiedLoads: 0 RemovedLoads: 0
... ... @@ -252,7 +252,7 @@
252 252  MC4>progreset
253 253  ...
254 254  CI ShowRunner startup completed successfully in 8072ms
255 -MC4>sr discover zummesh false
210 +MC4>sr discover zum false
256 256  Starting Zum Discovery without gateway claiming
257 257  MC4>Notice: SimplSharpPro[App01] # 2020-07-21 22:19:46 # Recalling startup scenes (if applicable)
258 258  Performing Discovery on 1 Gateways.
... ... @@ -302,4 +302,5 @@
302 302  Modified Loads: 0
303 303  Removed Loads: 0
304 304  Zum Discovery Finished
305 -}}}
260 + }}}
261 +)))