Skip to Content

Changes for page Zūm Discovery

Last modified by Alexander Mott on 2025/04/03 17:35
From version 12.1
edited by Alexander Mott
on 2022/10/06 14:25
Change comment: There is no comment for this version
To version 9.1
edited by Alexander Mott
on 2022/10/05 16:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -8,6 +8,8 @@
8 8  {{toc/}}
9 9  {{/box}}
10 10  
11 +(% class="row" %)
12 +(((
11 11  If Zūm Wired or Wireless devices have been configured using Crestron's Zūm App, then it is possible to automatically build a SHOWRUNNER™ configuration file using the Zūm Discovery feature that is built into SHOWRUNNER™.
12 12  
13 13  There are certain pre-requisites and limitations when building a SHOWRUNNER™ configuration this way, and it may sometimes be necessary make some adjustments to the final configuration, such as changing keypad types and moving loads between areas.
... ... @@ -51,10 +51,10 @@
51 51  1. Repeat from step 3 until all ZUMNET-JBOXs that are to be controlled by SHOWRUNNER™ have static IP addresses and unique CIDs for any hosted devices
52 52  1. Disconnect from any ZUMNET-JBOXs and then connect to the processor in Toolbox
53 53  1. Run the command: ##sr discover zumnet true false##
54 -1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding IP Devices to the configuration
56 +1*. This command tells SHOWRUNNER™ to discover all ZUMMNET-JBOXs on the network, configure their IP tables, and then add corresponding areas and loads to the configuration
57 +1*. One area will be created per ZUMNET-JBOX
55 55  1. Run the command: ##sr discover zumnet true true##
56 -1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware (including the internal ZUMNET-JBOX load controller) on the previously discovered Zūm Net devices and then add corresponding areas, loads, sensors, etc. to the configuration
57 -1**. One area will be created per ZUMNET-JBOX, and all hardware attached to that ZUMNET-JBOX will be assigned to that area
59 +1*. This command tells SHOWRUNNER™ to discover all Zūm Link hardware on the previously discovered Zūm Net devices
58 58  1*. This command **does not** bring in Cresnet devices: those must be added to the configuration manually until this issue is fixed in the Zūm Wired firmware
59 59  1. Put all ZUMNET-JBOXs into CNET mode in order to allow full control from SHOWRUNNER™
60 60  1*. Odd behavior may result from conflicts between SHOWRUNNER™ and internal logic if the ZUMNET-JBOXs are not put into CNET mode
... ... @@ -62,6 +62,7 @@
62 62  = Zūm Wireless Discovery =
63 63  
64 64  == Notes and Limitations ==
67 +)))
65 65  
66 66  (% class="box errormessage" %)
67 67  (((
... ... @@ -81,6 +81,8 @@
81 81  1. **Claim All RF Gateways** - SHOWRUNNER™ will find all CEN-GWEXERs [ZUMNET-GATEWAY] on the network and will claim them as its own. **DO NOT** use this method if there are gateways used by different SHOWRUNNER™ or other Crestron systems on the same local network.
82 82  )))
83 83  
87 +(% class="row" %)
88 +(((
84 84  == Manual RF Gateway Assignment Instructions ==
85 85  
86 86  Use this method if you have multiple SHOWRUNNER™ instances on the same network or have gateways used by other Crestron systems.
... ... @@ -302,3 +302,4 @@
302 302  Removed Loads: 0
303 303  Zum Discovery Finished
304 304  }}}
310 +)))