Skip to Content

Changes for page GLS-ODT-C-NS and CN

Last modified by Alexander Mott on 2021/12/08 00:15
From version 3.1
edited by Craig Lewis
on 2020/05/14 18:13
Change comment: There is no comment for this version
To version 12.1
edited by Alexander Mott
on 2021/12/08 00:15
Change comment: Renamed from xwiki:SHOWRUNNER™ User Guide & Wiki.Design Guide.Hardware Design Guide.GLS-ODT-C-NS.WebHome

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -GLS-ODT-C-NS
1 +GLS-ODT-C-NS and CN
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.craig\.lewis@chiefintegrations\.com
1 +XWiki.alexander\.mott@chiefintegrations\.com
Content
... ... @@ -1,16 +1,18 @@
1 -I went through a similar analysis with our team’s own reporting of issues with 3 GLS-ODT-C-CNs on projects.  Don’t know if the problem is due to a material change mid-production or has always been incorrect but it is problem with shipping hardware.
1 +(% class="wikigeneratedid" %)
2 +The GLS-ODT-C-NS is a ceiling-mounted occupancy sensor designed to provide coverage for areas up to 2,000 square feet. The sensor utilizes both passive infrared (PIR) and ultrasonic (US) motion sensors to allow reliable motion detection. The GLS-ODT-C-NS can be used in standalone applications when paired with a GLPP, GLPAC, or GL-IPAC.
2 2  
4 +=== Note on GLS-ODT-C-NS and GLS-ODT-C-CN Power Draw ===
3 3  
4 -Crestron has had the specs on the GLS-ODT-C-NS sensors wrong and we haven’t been able to get them corrected.  The sensors actually draw ~~60mA.  We’ve done a number of jobs with GLPPs that don’t perform correctly because of the over-current situation created by 3 or more GLS-ODT-C-CNs attached to a GLPP.  Last I heard Crestron tech support was acknowledging 3 sensors was too many on the GLPP and was advising TR-100s or other external power if more than 2 sensors were used.
6 +The listed power draw for GLS-ODT-C-NS and CN sensors is 45mA at 24VDC, however Chief Integrations' testing with shipped hardware shows the real-world power draw to be closer to 60mA. While GLPP modules are able to provide 150mA at 24VDC for sensors, this is insufficient for real-world applications involving more than two GLS-ODT-C-NS occupancy sensors.
5 5  
8 +As such, Chief Integrations recommends adding a GLA-TR-100 or other external power supply if more than two sensors are required to be added to one GLPP.
6 6  
7 -Here's an analysis we’ve performed with our own inventory of hardware:
10 +=== Detailed Analysis ===
8 8  
9 -Below measurements were taken with GLS-ODT-C-NS (SN 15772519) attached to GLPP-1DIMFLV2CN-PM (SN 17386110) with ~~1’ of wire length with a Pokit portable oscilloscope in line to capture the current.  The initial soft start (~~270ms) is followed by full operation which draws ~~60mA.  60mA average consumption is fairly stable for the remainder of the sensor’s runtime.  PIR , US A and B are enabled as are the LEDs on this unit.  Turning off some of those functions may reduce the current consumption but we have not measured them.  Similar measurements were obtained with a Fluke 189 DMM so we know this Pokit capture is accurate.  Alternative measurements were taken with an HP 6632A DC power supply as the 24VDC power source and similar readings were produced and confirmed by the power supply’s internal meter.
12 +The below measurements were taken with GLS-ODT-C-NS attached to a GLPP-1DIMFLV2CN-PM with ~~1’ of wire using a Pokit portable oscilloscope in line to capture the current.  The initial soft start (~~270ms) is followed by full operation which draws ~~60mA.  60mA average consumption is fairly stable for the remainder of the sensor’s runtime.  PIR, US A and B are enabled as are the LEDs on this unit.  Turning off some of those functions may reduce the current consumption but we have not measured them.  Similar measurements were obtained with a Fluke 189 DMM so we know this Pokit capture is accurate.  Alternative measurements were taken with an HP 6632A DC power supply as the 24VDC power source and similar readings were produced and confirmed by the power supply’s internal meter.
10 10  
14 +Note, a similar test has been done on a GLA-IR-QUATTRO-HD-COM1-24. These sensors are listed as requiring 32mA at 24VDC, however testing shows that the sensors actually draw ~~60mA on startup before dropping to 20mA steady state within 50ms.
15 +
11 11  [[image:image-20200514111237-1.jpeg]]
12 12  
13 -
14 -Note, the Steinel IR Quattro HD sensors draw ~~60mA at startup but within 50ms drop down to 20mA steady state and remain there.  The Steinel sensors also have better coverage in our experience.
15 -
16 -[[image:image-20200514111237-2.png]]
18 +//GLS-ODT-C-NS current draw readings.//