Skip to Content
Last modified by Alexander Mott on 2023/12/08 18:37
From version 14.11
edited by Alexander Mott
on 2023/03/27 19:33
Change comment: (Autosaved)
To version 14.6
edited by Alexander Mott
on 2023/03/27 19:13
Change comment: (Autosaved)

Summary

Details

Page properties
Content
... ... @@ -88,26 +88,8 @@
88 88  
89 89  == Standalone ==
90 90  
91 -Completely standalone Zūm Wired designs are possible, but they have some important benefits and drawbacks to consider.
91 +Lorem
92 92  
93 -Some benefits of a standalone Zūm Wired system are:
94 -
95 -* Reduced installation time and cost as no Zūm Net cabling is required between rooms
96 -* Reduced hardware cost as no ZUM-HUB4 or networking hardware is required
97 -
98 -Some drawbacks of a standalone Zūm Wired system are:
99 -
100 -* As of 2/2023, ZUMNET-JBOX-* devices ship with factory settings that are incompatible with an App only startup, resulting in extra expense to configure and update devices prior to installation or extra time spent during startup to accomplish these tasks post-installation:
101 -** ZUMNET-JBOX-* devices must be manually set to Zūm App mode
102 -** ZUMNET-JBOX-* devices must be manually set to Primary mode
103 -** Updating firmware with the Crestron Zūm App is not possible with out-of-the-box firmware and must be initially done through Toolbox
104 -* ZUMNET-JBOX-* devices can only be connected to and configured via the App if there is a ZUMLINK-KP on their Zūm Link bus. During start-up, a technician must bring a ZUMLINK-KP with them to connect to the ZUMNET-JBOX for any rooms that were not designed to have a ZUMLINK-KP
105 -* No scheduling capabilities
106 -* No cross-room control capabilities (i.e., ZUMLINK-* keypads and occupancy sensors are restricted to controlling loads that are attached to the same ZUMNET-JBOX as they are)
107 -* No support for Cresnet devices
108 -* No support for third-party integrations beyond the override contact-closure relay at each ZUMNET/ZUMLINK-JBOX and the relay output of any *-RLY model occupancy sensors
109 -* No support for DMX control
110 -
111 111  == Networked ==
112 112  
113 113  Lorem
... ... @@ -114,26 +114,20 @@
114 114  
115 115  === Networked with Default Program ===
116 116  
117 -Some benefits of using the default program are:
99 +Lorem
118 118  
119 -*
120 -
121 -Some drawbacks of using the default program are:
122 -
123 -* Requires a ZUM-HUB4 processor
124 -* Limited support for Cresnet devices on the Zūm Link bus (n**o support?**)
125 -* Limited scheduling capabilities
126 -
127 127  === Networked with Custom Program ===
128 128  
129 -Some benefits of using a custom program such as SHOWRUNNER™ are:
103 +Lorem
130 130  
131 -*
105 +== Start-Up Considerations ==
132 132  
133 -Some drawbacks of using a custom program such as SHOWRUNNER™ are:
107 +Lorem
134 134  
135 -*
109 +== Processor Selection for Networked Systems ==
136 136  
111 +Lorem
112 +
137 137  = Hardware Design Limitations =
138 138  
139 139  There are a handful of limitations to keep in mind when designing Zūm Wired systems, with different restrictions applying to Zūm Net and Zūm Link: